[porkcereal]

18x9.5 +40 niche verona with 2454018 michelin pss.

 

[GtSell06]

18x9.5 +40 niche verona with 2454018 michelin pss.

Hey man is your car lowered at all and are you running spacers?

 

[porkcereal]

Hey man is your car lowered at all and are you running spacers?

Stock height. 18x9.5 +40

Sent from my SAMSUNG-SM-G935A using Tapatalk

 

[DsFocusST1]

Looks good dude! Funny story, as you looked into the ones on mine, I actually almost went with these over the VP5s. Looks good though!

 

[porkcereal]

Looks good dude! Funny story, as you looked into the ones on mine, I actually almost went with these over the VP5s. Looks good though!

Ha, i went with these over the vp5s. Was going to have them drilled and shaved the same. About 400 less for what i got.

Sent from my SAMSUNG-SM-G935A using Tapatalk

 

[ManzoniST]

18x9.5 +40 niche verona with 2454018 michelin pss.

Plus 40 offset right? Dumb question but is that why they are concaved?

 

[porkcereal]

Plus 40 yes, they are concaved due to the 9.5 width and the design. The 40 just keeps them a little more under the fenders than Grids.

 

[ManzoniST]

Plus 40 yes, they are concaved due to the 9.5 width and the design. The 40 just keeps them a little more under the fenders than Grids.

You familier with the mrr gf7's do you think plus 44 will be just outside fenders ?

 

[porkcereal]

+44 with a 9
Depends on the width, a 9.5 you can do a +42. I saw a pick of this setup and it was close to not clearing the inside, i wouldnt do any more than 42.
The good thing about MRR is they will shave any offset you like.

 

[ManzoniST]

Cool well the bad thing with this is im not familier with offset

 

[Quantim0]

You familier with the mrr gf7's do you think plus 44 will be just outside fenders ?

I have a 9.5 et45 on my car and it clears the coil overs on the inside by about a millimeter. I don't think you'd clear on struts. I'm flush with the fenders with - 2 camber

Sent from my Nexus 6P using Tapatalk

 

[jpolka13]

Someone please help.

I have a friend selling a set of 18x10 +25 wheels from his evo.
I found will adapters to go from our 5x108 to the more common 5x114.3, but they are 15mm thick.

I've read this forum and I'm having a difficult time comprehending all this wheel stuff. LOL

My question is, will these fit? If i could get an explanation rather than a simple yes/no that'd be awesome.

Thanks in advance!

 

[ZX3ST]

Someone please help.

I have a friend selling a set of 18x10 +25 wheels from his evo.
I found will adapters to go from our 5x108 to the more common 5x114.3, but they are 15mm thick.

I've read this forum and I'm having a difficult time comprehending all this wheel stuff. LOL

My question is, will these fit? If i could get an explanation rather than a simple yes/no that'd be awesome.

Thanks in advance!

The 15mm spacers basically bring that wheel to +10 offset. Using this handy little calculator:
Online Wheel and Tyre Fitment Calculator. Offset, Tyre Stretch and Speedo Error | Will They Fit

Your setup would stick out 2.77" further than stock. You're looking at heavy fender mods.

 

[Sparky]

New set of wheels:

BRAID Fullrace A flowform monoblock
satin black, painted
18x9.0
et48

 

[Sparky]

Some dynamic shots at Laguna Seca.

Particularly telling is the shot coming down the corkscrew with left side fully loaded. At full compression, there is very minimal but complete clearance between outer fender and tire. I think the +48 offset is necessary for complete clearance when running a 255 or higher tire. As some other members stated they are successfully running +38 offsets on track, I think this is dependent on the fact that they are also running 235 tires. Just my 2 cents.

Photos courtesy of Dito Milan, gotbluemilk.com

 

[Sparky]

Sorry not sure what happened to the Corkscrew shot on prev post. The one in prev post is at top of corkscrew where left is relatively UNloaded. At the bottom, there is full compression. Will try again.

Tires are Toyo R888 255/35-18

 

[haydenbrutal]

18x9 +38 lowered on steeda springs

 

[RoachRage]

Bluetiful

18x9 +38 lowered on steeda springs

 

[Focust st 2014]

18x9 +38 lowered on steeda springs

That's looking good!! Defiantly like the lip and the dish of the wheels. What wheels are those?

 

[adizon]

Finally got some wheels
TSW 18x8.5 +43, on OEM Goodyears